Corrosion characteristics of aluminium alloy graphite particulate composite in various environments

The present study was aimed at understanding the response of 2014 Al alloy dispersed with graphite particles in various corrosive environments. Marine (sodium chloride) as well as acidic media were selected for the purpose with a view to widen the range of utility of the composite for applications where such environments may be encountered. Studies were also extended to characterize the corrosion resistance of the composite in fresh as well as used lubricating oils to explore the possibilities of using it in bearing, bushing and such other applications. The corrosion behaviour of the base alloy processed under identical conditions was also examined in the above media to see the influence of graphite addition in the alloy. In order to assess the role of the matrix microstructure, the composite as well as the base alloy was subjected to corrosion in heat-treated as well as-cast conditions. It was observed that the specimens suffered from the maximum rate of corrosion in acid, while sodium chloride produced the minimum corrosion rate. Oil in both used and fresh conditions revealed a negligibly small extent of corrosion. The composite was found to show a higher rate of corrosion than the base alloy under identical test conditions. This was attributed to the dispersoid/matrix interfacial corrosion in the case of the graphitic aluminium alloy. Heat treatment of the composite and the base alloy was found to lower the rate of corrosion in the environments tested. Microstructural modifications of the matrix and possible relief of residual stresses were thought to be responsible for the lower rate of corrosion in the heat-treated condition.     

An analysis of the electrical conductivity in BaSO4-added Ag2SO4 solid electrolyte system

The compositions (1 −x)Ag₂SO₄−(x)BaSO₄, wherex=0·01 to 0·6, were prepared by slow cooling of the melt. The extent of the solid solubility of Ba²⁺ in Ag₂SO₄ was determined by X-ray powder diffraction and scanning electron microscopy. The bulk conductivity of each sample was obtained using a detailed impedance analysis. The partial substitution of Ba²⁺ results in the enhancement of conductivity in compliance with the classical aliovalent doping theory. A simplistic model based on lattice distortion (expansion) due to partial substitution of Ag⁺ by the bigger Ba²⁺ has been considered to explain enhanced conductivity. Beyond solid-solubility limit (5·27 mole%) the BaSO₄-dispersed Ag₂SO₄ conductivity follows the usual trend seen in binary systems. An increase in conductivity in this case is discussed in the light of interfacial reactions and surface defect chemistry. The maximum conductivity in 20 mole% BaSO₄ dispersed Ag₂SO₄ is due to percolation threshold.     

A fast-settling GaAs-enhanced frequency synthesizer

An indirect, phase-locked-loop (PLL), GaAs-enhanced frequency synthesizer with 700 ns loop settling time has been developed. The two-chip GaAs insertion reduced the size of an existing synthesizer from 90 in³ to only 30 in³. The 6.0 in×5.5 in.×0.9 in module contains a 400 gate GaAs programmable divider and a sample and hold (S/H) which improved the settling time by 77% and reduced the size by 67% over the current state-of-the-art synthesizer. Furthermore, the divider reduced power dissipation by 9.7 W and the S/H reduced power dissipation by 1.3 W     

Response spectrum analysis of piping systems with elastic-plastic gap supports

A new seismic support device and its application in piping systems is described. The device, E-BAR (patented), can be cost effectively used for snubber replacement programs, mitigation of hydraulic transients, pipe whip and as a thermal stop. The device has pre-set gaps to allow free thermal movement. During a seismic or other dynamic load event, if the pipe movement exceeds the gap dimension, the device acts as an elastic or elastic-plastic restraint. The device also has a unique design feature for not exceeding the restraint force beyond a specified limit design value. To analyze piping systems with gap supports having elastic-plastic characteristics, modal analysis procedures for both response spectrum and time history methods are developed. The comparison of responses obtained from the procedures with nonlinear time history analysis and test results available in the literature shows excellent correlation. A pilot program conducted for snubber replacement with E-BARs demonstrates that the limit force feature of E-BAR makes them very attractive for snubber replacement. This is because a particular E-BAR with a specified limit design force can be selected, such that, the E-BAR replacing the snubber does not require any modifications be made to the existing support steel and hardware.     

A high-current and high-temperature 6H-SiC thyristor

A 6H-SiC thyristor has been fabricated and characterized. A forward breakover voltage close to 100 V and a pulse switched current density of 5200 A/cm² have been demonstrated. The thyristor is shown to operate under pulse gate triggering for turn-on and turn-off, with a rise time of 43 ns and a fall time of less than 100 ns. The forward breakover voltage is found to decrease by only 4% when the operating temperature is increased from room temperature to 300°C. It is found that anode ohmic contact resistance dominates the device forward drop at high current densities     

Evaluation of the recombinant 38-kilodalton antigen of Mycobacterium tuberculosis as a potential immunodiagnostic reagent

The diagnosis of infection caused by Mycobacterium tuberculosis is of increased public health concern following increases in the number of cases in developed countries and major increases in developing countries associated with the spread of human immunodeficiency virus (HIV) infection. The specificity of purified protein derivative skin testing for the detection of infection is compromised by exposure to environmental mycobacteria. Examination of sputum detects the most infectious patients, but not those with extrapulmonary disease. The 38-kDa antigen of M. tuberculosis contains two M. tuberculosis-specific B-cell epitopes. We overexpressed the gene for this antigen in Escherichia coli and evaluated the recombinant product in in vitro assays of T-cell function and as a target for the antibody response in humans. The sensitivity and specificity of the antigen as a skin test reagent were also assessed in outbred guinea pigs. We found that 69% of healthy sensitized humans recognize the antigen in vitro, as manifested by both cell proliferation and the production of gamma interferon. Untreated patients initially have a lower frequency of response (38%); this recovers to 72% during therapy. A total of 292 patients (20 with HIV coinfection) and 58 controls were examined for production of antibody to the 38-kDa antigen by using a commercially available kit. The sensitivity of the test in comparison with that of culture was 72.6%, and the specificity was 94.9%. The antigen was also tested for its ability to induce skin reactions in outbred guinea pigs sensitized by various mycobacterial species. The antigen provoked significant skin reactions in M. tuberculosis-, M. bovis BCG-, and M. intracellulare-sensitized animals. The significance of these findings and the usefulness of this antigen in immunodiagnosis are discussed.     

Safety,liveness and fairness in temporal logic

In this paper we present syntactic characterization of temporal formulas that express various properties of interest in the verification of concurrent programs. Such a characterization helps us in choosing the right techniques for proving correctness with respect to these properties. The properties that we consider include safety properties, liveness properties and fairness properties. We also present algorithms for checking if a given temporal formula expresses any of these properties.This work is partly supported by NSF grant CCR-9212183. A preliminary version of this paper appeared in the Fourth ACM Symposium on Principles of Distributed Computing.